Development of Motorcycle Brake Oil Control System Using Arduino Uno R3 Based Pressure Sensor
Anastasia K. Utapara
Department of Physics, Udayana University, Bali, Indonesia.
A. A. Agung Ngurah Gunawan *
Department of Physics, Udayana University, Bali, Indonesia.
I. Nengah Sandi
Department of Physics, Udayana University, Bali, Indonesia.
I. Gusti Agung Widagda
Department of Physics, Udayana University, Bali, Indonesia.
Komang Ngurah Suarbawa
Department of Physics, Udayana University, Bali, Indonesia.
I. Gusti Agung Ayu Ratnawati
Department of Physics, Udayana University, Bali, Indonesia.
*Author to whom correspondence should be addressed.
Abstract
An alarm or reminder has been successfully designed to remind us when it is time to fill the brake fluid so as to avoid accidents when riding a motorbike with electronic components which are arranged, including Nex motorbike, Dot-3 brake fluid, Arduino Uno, Psi100 oil pressure sensor, red LED, Step down DC to dc, Resistor 220 0hm. The alarm was designed on the motorbike to serve as a reminder to fill the brake fluid before it decreases. In this research, calibration was carried out on the measuring instrument used so that the output produced by the sensor was the same as the digital measuring instrument, with an accuracy percentage level of 94.11%. The alarm system works when the pressure is low, the pressure sensor will read and process it on the Arduino, after processing the condition will be changed according to the pressure read by the sensor so when it is low the Arduino relay will provide voltage to the LED so that the LED can light up as a warning sign that the brakes are not working. good for use, and vice versa, when the brake fluid is full or meets standards, the relay will not be active and the motorbike will remain stable or can be used as usual.
Keywords: ATMega328 microcontroller, brake fluid, control system, indicators, sensors
How to Cite
Downloads
References
Artanto D. Arduino and Labview Interaction, Jakarta: PT Elex media kompotindo. 2012;7:145-149.
Turnip MT, Gunawan AAN, Adnyana IGAP, Supardi IW, Trisnawati NLP. Obstacle Detection Stick for the Visually Impaired Using HC-SR04 Ultrasonic Sensor and Arduino Nano Microcontroller-based Raindrop Sensor, Journal of Engineering Research and Reports. 2023;25(3):1–6.
Putra RR, Hamdani, Aryza S, Manik MA. Automatic School Bell Scheduling System Based on RTC Using Microcontroller. Journal of Budidarma Informatics Media. 2020;4 (2): 386-395.
Artawan MD, Gunawan AAN, Sumadiyasa M. Use of Short Message Service (SMS) Based ATmega328 Microcontroller and SIM800L Modules as on/off Control Electronic Equipments. Advances in Applied Physics. 2018;6(1):19-24.
Iwan NG, Saiful AI. Analysis of forces on disk brakes (Disk Brake) on two-wheeled vehicles (Honda Beat Sporty 2017). Journal of Mechanical Engineering Education. 2021;8(2).
Persada AAB, Persada YN, Gunawan H. Electrical System Design on Automatic Car Brake Oil Filling Tool, Eleman Journal. 2019;6 (1):36-39.
Maulavi R. Servo Operating Valve Actuator Design on Prototype and Boiler Simulator in Instrumentation Workshop, Thesis, Sepuluh September Institute of Technology, Surabaya; 2017.
Kunthi MR, Gunawan AAN, Ratini N. Making Monitoring Device of Infusion Liquid Using Proximity Photodiode as a Sensor Based on Arduino Uno, Contemporary Engineering Sciences. 2020;13(1):315-321.
Jamal N, Siswanto. Arduino and Android Based Room Security Monitoring Using VC0706 Camera, and DHT-11 Temperature Sensor, Journal of Informatics Engineering, Faculty of Information Technology, Budi Luhur University. 2018;1(3):1219-1224.
Turang DAO. Development of a Relay System for Controlling and Saving the Use of Mobile-Based Lights, Prosaiding Semnasif. 2015;1(1):75-85.
Akbar B, Alfian. Water Temperature Controller Using Arduino Uno Based DS18B20 Sensor. Final Project, D-II Physics Study Program FMIPA, University of North Sumatra; 2017.
Santoso SP, Wijayanto F. Door Access Design with Temperature Sensor and Arduino-based Automatic Handsanitizer, Electro Journal. 2022;10(1):20 – 31.